cutting hardness的例句大全

By cutting different hardness concrete experiment, the cutting characteristics of the special saw with holes or different width segment have been studied.

对多孔锯片及非等间距锯片进行了锯切三种不同硬度的混凝土的实验研究。

Wear resistance improves as cutting tool hardness increases.

削刃口耐磨，易磨损。削硬越，耐磨性越。

New Technology of Cutting High Hardness Roller Sheet in Fine Cokes Roller-type Crusher

焦粉四辊破碎机高硬度辊皮切削的新工艺

This material possesses high strength and toughness, its wear resistance being similar to that of ceramics. As a result, these tools show good performance in cutting high hardness materials.

这种刀具材料的耐磨性与陶瓷材料相近，并具有较高的强度和韧性，在切削高硬度材料时表现出良好的性能。

A Study of Martensitic Stainless Steel with Free-Cutting and High Hardness

易切削高硬度马氏体不锈钢研究

The most important properties of cutting tools are hardness at high temperature, wear resistance, and impact strength.

切削刀具最重要的性能是在高温下能保持的硬度、耐磨损和冲击韧性。

In the practical application of the equipment, fracture splitting defects such as drop clinker and slag inclusion can be reduced and the laser cutting parameters and hardness of lower limit can be improved.

裂解槽激光加工自动化设备在实际应用中，能够减少爆口、夹渣等裂解缺陷，并可以通过改变激光切割参数，改善硬度处于裂解工艺要求下限的连杆的裂解质量。

Hardness than corundum, abrasive easily broken, sharp edges and corners, good cutting, grinding heat and small.

硬度高于棕刚玉, 磨粒易破碎, 棱角锋利, 切削性能好, 磨削热量小等.

After isothermal normalizing, SAE 8620 H steel gear obtained the ideal hardness, micro structures and fine cutting behaviors.

SAE8620H钢齿轮采用等温正火工艺,获得了理想的硬度 、 金相组织和良好的切削性能.

Strength in cutting-tool material is not always proportional to hardness.

切削刀具材料的强度并不都是与硬度成正比的.

In addition, cut hardness decreases, heat affected zone width reduces and the size of grain gets smaller during underwater cutting.

超声频脉冲的作用还使得水中切割时切口硬度降低，热影响区宽度降低、晶粒变细小。

Besides, the experimental result shows that it is possible to machine the middle hardness surface gears on an ordinary bobbing machine under the rational cutting conditions.

测试结果表明：在合理的削切条件下，在普通滚齿机上实体滚切中硬齿面齿轮是完全可能的。

All metal cutting tools begin to lose hardness when heated to sufficiently high temperatures.

达到一定高温高时,所有的金属切削刀具便开始软化.

The Polycrystalline diamond ( PCD) has been applied widely in industrial fields as a new cutting tool material of high hardness and good wear-resistance. This thesis designed a type of PCD groove cutter by means of piston ring groove function.

随着聚晶金刚石（PCD）刀具材料在切削铝合金上的广泛应用，本文根据活塞环槽的性能要求及铝合金的切削特点，确定了PCD槽刀几何角度，设计了PCD环槽成型刀具。